ARCHORA / بيانات تقرير الاختبار المؤرشف
ألواح ألياف الخيزران والخشب · خصائص الحريق
竹木纤维板·燃烧性能
جداول خاصة بالمنتج مع المصدر ونطاق العينة لكل قيمة.
نسخة البيانات الفنية · الإنجليزية / الصينية · 48 KB
الملف الصيني الأصلي PDF ↗
نطاق البيانات
Fire-test specimen: 300 × 2800 mm; report conclusion: B1. The physical-property report uses a different specimen size. Do not combine the two as a universal specification guarantee.
| الخاصية | الوحدة | المعيار في المصدر | النتيجة المسجلة |
|---|---|---|---|
| Fire growth rate index FIGRA0.4MJ燃烧增长速率指数 FIGRA0.4MJ | W/s | ≤250 | 226 |
| Total heat release THR600s600s总放热量 THR600s | MJ | ≤15 | 8 |
| Lateral flame spread火焰横向蔓延 | Does not reach long-wing edge | Did not reach long-wing edge | |
| Flame-tip height within 60 s60s内焰尖高度 Fs | mm | ≤150 | <150 |
| Filter-paper ignition by flaming droplets within 60 s60s内燃烧滴落物引燃滤纸 | No ignition | No ignition |
نسخة البيانات الفنية · الإنجليزية / الصينية · 48 KB
الملف الصيني الأصلي PDF ↗صفحات التقارير الأصلية
نسخ مقروءة من التقارير؛ تتوفر ملفات PDF الأصلية الكاملة مع البيانات الفنية.
أنظمة الألواح: التشطيبات والتفاصيل والوثائق
أربع عائلات تشطيب وخمسة أنواع مكونات، مع صور تطبيق ومراجع عينات أصلية ودليل تخطيط فني.
كتيب المنتجات
12 صفحات · 3.0 MB · الإنجليزية / الصينية
تنزيل PDF ↓الدليل الفني والتركيب
21 صفحات · 6.7 MB · الإنجليزية / الصينية
تنزيل PDF ↓الدليل الكامل للألواح
72 صفحات · 14.3 MB · الإنجليزية / الصينية
تنزيل PDF ↓كتالوج العينات الأصلي
39 صفحات · 4.6 MB · 中文
تنزيل PDF ↓تصف التقارير عينات محددة، ولا تعتمد تلقائياً جميع التشطيبات والسماكات والقطاعات أو الأنظمة المركبة.
المعايير ومراجع المواصفات
إرشادات تفصيلية · الإنجليزية / الصينية · 2026-10-10
External references for specification planning; these values are not Kangyi test results or an ARCHORA supply guarantee. T/ZZB values refer to the paper/film-faced category.
外部资料用于选型与技术对标,不是康亿实测值或雅筑朗供货承诺;T/ZZB 指标对应纸膜类饰面。
Standard editions & limits / 标准版本与限值
- GB/T 24137-2009
- Current wood-plastic decorative board standard; also the basis named in the 2024 physical report. [S1]
现行木塑装饰板标准;亦为 2024 年理化报告所列依据。 - GB 18580-2025
- Effective 2026-06-01, replacing 2017. In its scope: wood-based panels ≤0.124 mg/m³ (E1); their finished products ≤0.050 mg/m³ (E0). Confirm classification and specimen preparation for the supplied material. [S2–S3]
2026-06-01 实施并代替 2017 版;适用范围内,人造板限量 ≤0.124 mg/m³(E1),人造板制品 ≤0.050 mg/m³(E0)。供货材料的适用分类与制样要求须核实。 - GB 8624-2012 / 2025
- The 2024 fire report uses 2012. The 2025 edition takes effect on 2027-01-01; it is not yet in force on this review date. [S4]
现有 2024 年燃烧报告依据 2012 版;2025 版于 2027-01-01 实施,本次检索日尚未实施。 - JGJ/T 478-2019
- Publisher lists it as current. Use the applicable interior-wall design, construction and acceptance provisions when developing the project system. [S9]
出版方列为现行;项目构造设计应核对其中适用的室内墙面设计、施工与验收条款。
Keep the 2024 results and original criteria unchanged. The 0.023 mg/m³ result does not itself establish E0/ENF certification or compliance under a later test edition.
保留 2024 年实测结果与原报告判据;0.023 mg/m³ 数值本身不等于 E0/ENF 认证,也不能直接替代新版条件下的检测结论。
14 industry benchmark parameters / 14 项行业对标参数
T/ZZB 1671-2025 · Tables 3–4 [S5]. Paper / film-faced category. External reference, not an ARCHORA conformity claim. / 纸膜饰面类对标,不是本产品合格声明。
| Parameter / 项目 | Unit | Reference / 对标值 |
|---|---|---|
| Length deviation / 长度偏差 | mm | 0 to +3 |
| Thickness deviation / 厚度偏差 | mm | ±0.3 |
| Width deviation / 宽度偏差 | mm | ±1 |
| Diagonal difference / 对角线差 | mm | ≤3.5 |
| Flatness / 平整度 | mm | ≤0.5 |
| Assembled seam / 拼缝间距 | mm | ≤0.3 |
| Density / 密度 | g/cm³ | 0.8–1.1 |
| Moisture content / 含水率 | % | ≤1.2 |
| Flexural strength / 抗弯强度 | MPa | Mean ≥20; minimum ≥16 |
| Flexural modulus / 抗弯弹性模量 | MPa | ≥1800 |
| Dimensional stability / 尺寸稳定性 | % | ≤0.4 |
| Shore hardness / 邵氏硬度 | HD | ≥58 |
| Thickness swelling / 吸水厚度膨胀率 | % | ≤0.3 |
| Surface bond / 表面胶合强度 | MPa | ≥0.5 |
Kangyi recorded hardness: HD 57; benchmark: HD ≥58. Do not assume group-standard conformity. The assembled seam criterion is not a site movement allowance. / 康亿实测硬度 HD 57,对标值 HD ≥58,不能据此推定符合团体标准;拼缝指标不等于现场伸缩缝。
Size & installation references / 规格与施工参考
- Recorded Kangyi specimen / 康亿送检规格
- 2800 × 600 × 9 mm
2024 physical report; specimen identity, not a full supply-size list. / 2024 理化报告送检尺寸,不代表全部供货规格。 - CREATEKING example [S6] / 厂家规格示例
- Length 2.8 / 3 m; width 600 mm; thickness 8 / 9 mm
PVC-film finish. Reference to another manufacturer, not an ARCHORA model. / PVC 覆膜,为其他厂家示例,不是雅筑朗型号。 - V COWOOD KM300 [S7] / 厂家规格示例
- Section 300 × 12 mm; usual length 3 m
Different section; custom length is stated by that manufacturer. / 不同截面,其厂家说明可定制长度。 - Acclimation reference [S8] / 环境适应参考
- 24–48 h
CREATEKING preparation guidance. Confirm the period for the supplied panel and site. / 来自其他厂家施工准备指南,本项目按实际供货及现场条件确认。
Online sources / 网络资料来源
- S1 · GB/T 24137-2009 — SAMR / 国家标准平台 ↗
- S2 · GB 18580-2025 — SAMR / 国家标准平台 ↗
- S3 · Formaldehyde limits / 新国标解读 — 国家林草局 ↗
- S4 · GB 8624-2025 — SAMR / 国家标准平台 ↗
- S5 · T/ZZB 1671-2025, tables 3–4 / 团体标准平台 ↗
- S6 · CREATEKING 600 mm bamboo-fibre wall panel / 厂家产品页 ↗
- S7 · V COWOOD KM300 / 维可森厂家产品页 ↗
- S8 · CREATEKING WPC installation / 厂家安装指南 ↗
- S9 · JGJ/T 478-2019 — publisher / 中国建筑标准设计网 ↗


