ARCHORA / جميع المنتجات
مكونات الألواح
اختر المادة والتشطيب لمشروعك. يساعدك فريقنا في تأكيد النظام المتوافق ومواصفات المنتج.

مكونات الألواح
قطاعات تشطيب
رسم تخطيطي للمكونات والتركيب، غير مقيّس. يُؤكد القطاع والتثبيت الفعليان.

مكونات الألواح
زوايا داخلية وخارجية
رسم تخطيطي للمكونات والتركيب، غير مقيّس. يُؤكد القطاع والتثبيت الفعليان.

مكونات الألواح
وزرات
رسم تخطيطي للمكونات والتركيب، غير مقيّس. يُؤكد القطاع والتثبيت الفعليان.

مكونات الألواح
حليات زخرفية
رسم تخطيطي للمكونات والتركيب، غير مقيّس. يُؤكد القطاع والتثبيت الفعليان.

مكونات الألواح
ألواح شرائحية
رسم تخطيطي للمكونات والتركيب، غير مقيّس. يُؤكد القطاع والتثبيت الفعليان.
اختر المادة والتشطيب لمشروعك. يساعدك فريقنا في تأكيد النظام المتوافق ومواصفات المنتج.
ناقش المواصفات ↗البيانات الفنية والوثائق الأصلية
جداول خاصة بالمنتج مع المصدر ونطاق العينة لكل قيمة.
مواصفات تحتاج إلى تأكيد (5)
يلزم تحديد طراز الطلب وورقة بيانات معتمدة للمنتج قبل نشر قيم الأداء.
- قطاعات تشطيب
- زوايا داخلية وخارجية
- وزرات
- حليات زخرفية
- ألواح شرائحية
أنظمة الألواح: التشطيبات والتفاصيل والوثائق
أربع عائلات تشطيب وخمسة أنواع مكونات، مع صور تطبيق ومراجع عينات أصلية ودليل تخطيط فني.
كتيب المنتجات
12 صفحات · 3.0 MB · الإنجليزية / الصينية
تنزيل PDF ↓الدليل الفني والتركيب
21 صفحات · 6.7 MB · الإنجليزية / الصينية
تنزيل PDF ↓الدليل الكامل للألواح
72 صفحات · 14.3 MB · الإنجليزية / الصينية
تنزيل PDF ↓كتالوج العينات الأصلي
39 صفحات · 4.6 MB · 中文
تنزيل PDF ↓تصف التقارير عينات محددة، ولا تعتمد تلقائياً جميع التشطيبات والسماكات والقطاعات أو الأنظمة المركبة.
تفاصيل المنتجات والمكونات
إرشادات تفصيلية · الإنجليزية / الصينية

قطاعات تشطيب
Finishes exposed panel ends and transitions to adjacent materials.
用于板材端部与相邻材料交接处收口。
التطبيقات
Wall ends, reveals, door returns and exposed panel edges.
墙面端部、洞口、门套交接及板材外露边。
الاختيار والمواصفات
Select the profile opening for the actual panel thickness; confirm finish, length and fixing method.
按实际板厚选择槽口,确认饰面、长度和固定方式。

زوايا داخلية وخارجية
Coordinates the internal and external corners of a panel installation.
处理板材安装中的阴角与阳角交接。
التطبيقات
Room corners, columns, returns and edge protection.
房间转角、柱角、返边及边缘保护。
الاختيار والمواصفات
Confirm actual angle, cover width and panel build-up; dry-fit corners before final fixing.
确认实际角度、覆盖宽度和板材构造,正式固定前试拼。

وزرات
Creates a controlled finish at the wall and floor perimeter.
完成墙地交接并遮盖按设计预留的周边缝。
التطبيقات
Wall bases in guestrooms, offices and living spaces.
客房、办公与居住空间墙脚。
الاختيار والمواصفات
Agree height, projection, corners and floor movement; allow access where maintenance is needed.
确认高度、出墙尺寸、转角和地面伸缩需求,检修部位保持可拆性。

حليات زخرفية
Adds linear framing and decorative divisions to a panel composition.
用于板面框线、线性装饰和构图分割。
التطبيقات
Feature walls, framed panels and coordinated room details.
背景墙、框线墙板及室内整体装饰。
الاختيار والمواصفات
Approve section, layout, joint positions and finish; the moulding is not a load-bearing member.
确认截面、排版、接头和饰面;装饰线条不作为承重构件。

ألواح شرائحية
A repeated linear profile for decorative wall surfaces.
以重复线性单元形成有层次的装饰墙面。
التطبيقات
Feature walls, entrance zones and decorative wall accents.
背景墙、入口及墙面装饰重点区域。
الاختيار والمواصفات
Confirm slat dimensions, pitch, backing and fixing. Acoustic or fire performance needs a matching assembly report.
确认条宽、深度、间距、背衬及固定;吸声或防火性能需对应构造报告。
تخطيط التركيب
إرشادات تفصيلية · الإنجليزية / الصينية

Survey & specify
Record the base, room use, moisture exposure, openings and service routes. Resolve water ingress and unsound surfaces before covering. Agree the exact board and installation system.
记录基层、空间用途、潮湿暴露、洞口和管线;先处理渗水与松散基层,再确认具体板材及安装体系。
Set out & approve
Measure the wall, plan joints and trims, and dry-lay panels by colour and grain. Approve a sample junction before the main installation.
测量墙面、安排拼缝和收口,按花色与纹理预排,先确认样板及节点再大面积安装。
Prepare the base
Use a sound, clean and suitably flat base. Where a support frame is needed, design its anchorage, spacing and corrosion protection for the project.
基层应牢固、清洁并满足平整要求;需龙骨时按项目设计锚固、间距和防腐措施。
Fix panels
Use the fixing method confirmed for the supplied panel. For bonding, check panel/base compatibility and follow the adhesive instructions. For mechanical fixing, use the approved clips or screws and support layout.
采用与供货板材一致的固定方式;胶粘时确认板背与基层兼容并遵守胶粘剂说明,机械固定时按确认的卡件、螺钉及支承排布施工。
Finish junctions
Provide the movement allowance specified for the panel and site conditions; do not force boards into place. Coordinate corners, floor edges, doors and service openings.
按板材及现场条件预留经确认的伸缩余量,不强行挤压安装;协调转角、墙脚、门洞和设备洞口。
Inspect & maintain
Check alignment, secure fixing, seams and surface condition. Clean gently with a soft cloth and a finish-compatible cleaner tested in a hidden area. Keep the approved sample and batch record.
检查垂直度、固定、拼缝和表面,以软布及经隐蔽处试验的适用清洁剂清洁,留存确认样板和批次记录。
قائمة الطلب والنظام
- Product & finish
- Exact model, finish code, batch and physical approval sample.
具体型号、花色编码、批次及确认实物样板。 - Geometry
- Length, width, thickness, section, edge type and agreed tolerances.
长宽厚、截面、边型及约定公差。 - System
- Base, supports, anchors, clips or adhesive, trims and movement details.
基层、支承、锚件、卡件或胶、收口及伸缩节点。 - Performance
- Match each report to the supplied model, finish, thickness and assembly.
逐份确认报告与供货型号、饰面、厚度及构造的适用关系。 - Delivery
- Quantity, cutting plan, packing, spare panels and care instructions.
数量、裁切计划、包装、备用板及维护说明。
المعايير ومراجع المواصفات
إرشادات تفصيلية · الإنجليزية / الصينية · 2026-10-10
External references for specification planning; these values are not Kangyi test results or an ARCHORA supply guarantee. T/ZZB values refer to the paper/film-faced category.
外部资料用于选型与技术对标,不是康亿实测值或雅筑朗供货承诺;T/ZZB 指标对应纸膜类饰面。
Standard editions & limits / 标准版本与限值
- GB/T 24137-2009
- Current wood-plastic decorative board standard; also the basis named in the 2024 physical report. [S1]
现行木塑装饰板标准;亦为 2024 年理化报告所列依据。 - GB 18580-2025
- Effective 2026-06-01, replacing 2017. In its scope: wood-based panels ≤0.124 mg/m³ (E1); their finished products ≤0.050 mg/m³ (E0). Confirm classification and specimen preparation for the supplied material. [S2–S3]
2026-06-01 实施并代替 2017 版;适用范围内,人造板限量 ≤0.124 mg/m³(E1),人造板制品 ≤0.050 mg/m³(E0)。供货材料的适用分类与制样要求须核实。 - GB 8624-2012 / 2025
- The 2024 fire report uses 2012. The 2025 edition takes effect on 2027-01-01; it is not yet in force on this review date. [S4]
现有 2024 年燃烧报告依据 2012 版;2025 版于 2027-01-01 实施,本次检索日尚未实施。 - JGJ/T 478-2019
- Publisher lists it as current. Use the applicable interior-wall design, construction and acceptance provisions when developing the project system. [S9]
出版方列为现行;项目构造设计应核对其中适用的室内墙面设计、施工与验收条款。
Keep the 2024 results and original criteria unchanged. The 0.023 mg/m³ result does not itself establish E0/ENF certification or compliance under a later test edition.
保留 2024 年实测结果与原报告判据;0.023 mg/m³ 数值本身不等于 E0/ENF 认证,也不能直接替代新版条件下的检测结论。
14 industry benchmark parameters / 14 项行业对标参数
T/ZZB 1671-2025 · Tables 3–4 [S5]. Paper / film-faced category. External reference, not an ARCHORA conformity claim. / 纸膜饰面类对标,不是本产品合格声明。
| Parameter / 项目 | Unit | Reference / 对标值 |
|---|---|---|
| Length deviation / 长度偏差 | mm | 0 to +3 |
| Thickness deviation / 厚度偏差 | mm | ±0.3 |
| Width deviation / 宽度偏差 | mm | ±1 |
| Diagonal difference / 对角线差 | mm | ≤3.5 |
| Flatness / 平整度 | mm | ≤0.5 |
| Assembled seam / 拼缝间距 | mm | ≤0.3 |
| Density / 密度 | g/cm³ | 0.8–1.1 |
| Moisture content / 含水率 | % | ≤1.2 |
| Flexural strength / 抗弯强度 | MPa | Mean ≥20; minimum ≥16 |
| Flexural modulus / 抗弯弹性模量 | MPa | ≥1800 |
| Dimensional stability / 尺寸稳定性 | % | ≤0.4 |
| Shore hardness / 邵氏硬度 | HD | ≥58 |
| Thickness swelling / 吸水厚度膨胀率 | % | ≤0.3 |
| Surface bond / 表面胶合强度 | MPa | ≥0.5 |
Kangyi recorded hardness: HD 57; benchmark: HD ≥58. Do not assume group-standard conformity. The assembled seam criterion is not a site movement allowance. / 康亿实测硬度 HD 57,对标值 HD ≥58,不能据此推定符合团体标准;拼缝指标不等于现场伸缩缝。
Size & installation references / 规格与施工参考
- Recorded Kangyi specimen / 康亿送检规格
- 2800 × 600 × 9 mm
2024 physical report; specimen identity, not a full supply-size list. / 2024 理化报告送检尺寸,不代表全部供货规格。 - CREATEKING example [S6] / 厂家规格示例
- Length 2.8 / 3 m; width 600 mm; thickness 8 / 9 mm
PVC-film finish. Reference to another manufacturer, not an ARCHORA model. / PVC 覆膜,为其他厂家示例,不是雅筑朗型号。 - V COWOOD KM300 [S7] / 厂家规格示例
- Section 300 × 12 mm; usual length 3 m
Different section; custom length is stated by that manufacturer. / 不同截面,其厂家说明可定制长度。 - Acclimation reference [S8] / 环境适应参考
- 24–48 h
CREATEKING preparation guidance. Confirm the period for the supplied panel and site. / 来自其他厂家施工准备指南,本项目按实际供货及现场条件确认。
Online sources / 网络资料来源
- S1 · GB/T 24137-2009 — SAMR / 国家标准平台 ↗
- S2 · GB 18580-2025 — SAMR / 国家标准平台 ↗
- S3 · Formaldehyde limits / 新国标解读 — 国家林草局 ↗
- S4 · GB 8624-2025 — SAMR / 国家标准平台 ↗
- S5 · T/ZZB 1671-2025, tables 3–4 / 团体标准平台 ↗
- S6 · CREATEKING 600 mm bamboo-fibre wall panel / 厂家产品页 ↗
- S7 · V COWOOD KM300 / 维可森厂家产品页 ↗
- S8 · CREATEKING WPC installation / 厂家安装指南 ↗
- S9 · JGJ/T 478-2019 — publisher / 中国建筑标准设计网 ↗
